Home Garden
# Home & Garden >> Home Appliances >> Washer & Dryers

How to Replace the Clutch on a Whirlpool Top Loader Washer

Just like the clutch in a car, the clutch in a Whirlpool top load washer transmits power from the motor to the driveline. In a washer, the driveline connects to the basket and agitator. A worn clutch can’t effectively transfer power, and will cause the motor to slip. Eventually, the clutch won’t transfer any power, and the washer will be unusable. You should replace the clutch on a Whirlpool top loader washer as soon as the motor starts slipping to prevent damage.

Things You'll Need

  • Phillips-head screwdriver
  • Flat-head screwdriver
  • Socket wrench
  • Sockets
  • Pliers
Show More

Instructions

    • 1

      Unplug the washer from the electrical outlet.

    • 2

      Remove the two Phillips-head screws from the control panel. Flip the panel until it's behind the washer and let it hang from its hinges. Pry off the metal clips securing the washer cabinet to the back panel with a flat-head screwdriver. Unplug the door switch wiring harness from the washer. Tilt the cabinet forward and lift it off the washer.

    • 3

      Loosen the clamps connecting the drain hoses to the pump. Pull the hoses off the pump housing. Unplug the wiring harness connected to the drive motor. Pry the retaining clips off the drive motor and pump. Pull both the motor and pump out of the washer.

    • 4

      Pull the top cap off the agitator. Remove the 9/16-inch bolt from the top of the agitator assembly. Pull the agitator assembly out of the washer basket.

    • 5

      Lay the washer on its back to access the gear case from underneath.

    • 6

      Remove the three bolts holding the gear case to the washer. Pull the gear case straight out of the washer.

    • 7

      Pry the large, flat washer off the shaft extending out of the gear case. Remove the ring located under the washer. Pry the retainer clip off the base of the shaft with a flat-head screwdriver. Slide the clutch assembly off the shaft.

    • 8

      Slide a replacement clutch onto the shaft. Snap the retainer clip around the base of the shaft. Slide the support ring onto the shaft, followed by the flat washer. Slide the shaft into the washer and align the mounting holes in the gear case with the holes in the washer frame. Insert and tighten the three retaining bolts. Turn the washer upright.

    • 9

      Slide the agitator assembly onto the shaft in the washer tub. Insert and tighten the 9/16-inch bolt to secure the agitator. Place the top cap on the agitator and press down on it until it snaps into place.

    • 10

      Place the drive motor and pump in the washer. Secure the pump and motor using the mounting clips. Connect the wiring harness to the motor. Slide the drain hoses onto the pump and tighten the clamps.

    • 11

      Place the front edge of the washer cabinet on the front of the washer frame. Tilt the cabinet back until it sits against the back panel. Install the clips in the top of the washer body to secure it to the back panel. Connect the wiring harness for the door switch. Flip the control panel forward, and secure it in place using the two Phillips-head screws.

Previous:

Next:

Washer & Dryers
  1. How to Replace the Transmission in a Kenmore Washer
  2. How to Replace the Whirlpool Clutch Assembly
  3. How to Replace the Seal on a Front-Loader Whirlpool Washing Machine
  4. How to Replace the Clutch on a Kenmore Washing Machine
  5. How to Replace a Washer Suspension Rod
  6. How to Replace the Inner Tub on a Maytag Front Loader
  7. How to Change the Clutch in a Whirlpool Ultimate Care
  8. How to Replace the Belt in the GE Top Loader Washer
  9. How to Replace the Motor Controller in a Maytag Neptune
  10. How to Replace the Clutch on a Maytag MAV9600 Washing Machine
  11. How to Replace the CCU in a Whirlpool Frontloader Washer
  12. How to Replace a Pump in a Whirlpool Front Loader

Home Garden © https://www.98905.com