Home Garden
# Home & Garden >> Furniture >> Tables

How to Make a Dinning Room Table

A dining room isn't complete without a table. Dining room tables are often a decorative centerpiece made from some hardwood. Oak, walnut, and maple are common choices. These woods are heavy and provide enough strength to make a table last for decades. Dining room tables sold in many stores can cost thousands of dollars. Building your own will allow you to spend only a fraction of that. In a day your table can be built and in your dining room.

Things You'll Need

  • 6 oak boards, 1-inch-by-5-inch-by-40-inch
  • Damp cloth
  • Wood glue
  • 4 clamps, 36-inch
  • Rubber mallet
  • Tape measure
  • 2 oak boards, 2-inch-by-4-inch-by-30-inch
  • Drill
  • Screw gun
  • 3/32-inch drill bit
  • Counter sinker, 3/8-inch
  • Square
  • 4 oak boards, 3-inch-by-3-inch-by-30-inch
  • 2 oak boards, 1-inch-by-3-inch-by-24-inch
  • Oak board, 2-inch-by-3-inch-by-22-inch
  • 32 wood screws, 3-inch
  • Chisel, 1-inch
  • Orbital Sander
  • Sand paper, medium and fine grade
  • Wood stain
  • Paint brush
Show More

Instructions

    • 1

      Edge glue the six 1-by-5 oak boards together by first wiping the 30-inch edges clean with a damp cloth, then applying a bead of glue. Use four clamps nine inches apart to secure. Tap boards with your rubber mallet to be sure that all sides boards are flush, including the ends. This will be your table top. Let the glue dry according to instructions.

    • 2

      Drill four evenly spaced 3/32-inch holes through the 2-inch-by-30-inch sides of each 2-by-4 board. Counter sink a 3/8-inch hole to a depth of 1 3/4-inches. Pre-drill a 3/32-inch hole for every screwing application in this project.

    • 3

      Remove the clamps and lay the top flat and horizontal. Lay your 2-by-4 board vertically on the table, so it is parallel with and 8-inches away from, the left 30-inch edge. The counter sunk holes should be facing up. Lay the other 2-by-4 board 8-inches from the right side in the same fashion. Screw through each hole into the top.

    • 4

      Stand a 3-by-3 board vertically so it is on the bottom right side of the left 2-by-4 board. One side should be flat against the 2-by-4, the other 3-inches from the end. Screw through the 2-by-4 into the 3-by-3 to secure the first leg. Screw the next leg 3-inches from the other end in the same fashion. Repeat this with the other 2-by-4 board 3-by-3s to finish your legs. Legs should be square and between the 2-by-4s.

    • 5

      Screw your 1-by-3 board perpendicularly to the two 3-by-3s that are attached to the same 2-by-4. It should be 15 inches from and parallel to the 2-by-4s. Repeat this process with the other two legs.

    • 6

      Place your 2-by-3 board perpendicularly between the middle of the 1-by-3s. Screw 1-by-3s into the ends. This will provide support.

    • 7

      Turn your table upright and use your chisel to scrape off any excess glue. Try not to gouge the wood. Sand the entire project with medium sandpaper, then with fine sandpaper.

    • 8

      Apply wood stain and let dry according to instructions.

Previous:

Next:

Tables
  1. How to Make a Brick Table
  2. How to Make a Nook Breakfast Table
  3. How to Make an Oval Dining Room Table
  4. How to Make a Board to Cover a Dining Table Top
  5. How to Make a Dining Room Table
  6. How to Make Your Own Cafe Table
  7. How to Make a Coffee Table With Wheels
  8. How to Make a Laptop Table
  9. How to Make a Rustic Dining Room Table
  10. How to Make a Simple 2-by-4 End Table
  11. How to Make a Lattice Board Wall
  12. How to Make a Quilting Room Table With an Old Door

Home Garden © https://www.98905.com